Notifications
Clear all
Topic starter
07/03/2019 9:22 am
this is a repost since this was just in the anabolic forum before.
My homebrew winny recipie !
I basically figured this one out on accident after numerous failed attempts at making an injectable winny that wouldnt crash.
Anyways here it is !
For this experiment say we are going to make 20ml @ 50mg/ml.
Add 1gram of powder to .40ml of BA and 3ml of BB. Mix and heat until the solution turns clear. winny has a melting point of about 400 so you will need to get this stuff HOT so be carefull !! Once it turns clear add 2ml of PEG400 then mix and let it cool down for a bit (you still do want it warm though) Filter it into your sterile vial.
Then simply add 13.85 of bacteriostatic water (put this through the filter as well the purge any leftover hormone) and shake and you now have injectable winny!!
Shake before use and it will not clump at all and goes through a 25g with no problems at all !!!!!
Topic starter
07/03/2019 10:09 am
please note though that you still need to shake any Suspension before drawing out of the bottle....
07/03/2019 10:42 am
very interesting, what is your total expense to make this? flip
07/03/2019 11:23 am
what is the benifit of injecting winny over just using an oral form?
" Bring the Pain"
Topic starter
07/03/2019 12:09 pm
LOL - hell if I know! cheap!!! you mean with the winny or without???
winny of course depends on how much you buy...
A bottle of peg400 (lasts forever) bottle of BB and BA and a filter shouldnt cost more than 15-20 bucks?? A bottle of each of those should make more than a few 50ml jugs....
07/03/2019 1:00 pm
what is the benifit of injecting winny over just using an oral form?
it avoids the first pass through the liver ,and so none of the hormone is lost.More bang for your buck bro.
07/03/2019 1:43 pm
LOL - hell if I know! cheap!!! you mean with the winny or without???
winny of course depends on how much you buy...
A bottle of peg400 (lasts forever) bottle of BB and BA and a filter shouldnt cost more than 15-20 bucks?? A bottle of each of those should make more than a few 50ml jugs....
What is the peg400? flip
09/03/2019 11:16 am
Thanx for the info So Solid
" Bring the Pain"
Topic starter
09/03/2019 11:47 am
What is the peg400? flip
PEG400 = Polyethylene Glycol
(PEG) is a polymer made for ethylene oxide. It comes in almost any MW, from 200 to 60,000. 400 to 12,000 are the most common with 400 the most common for liquids and 2,500 for solid. (Anything over 800 to 1,000 is a solid at room temp.) It is nontoxic at any reasonable level. It is nonpolar while having lots of hydroxyl functionality. This makes it great for getting things to stay soluble in oil. Used a lot for compatibility reasons. Can also be used as a painless vehicle, instead of oil. Drawbacks include high viscosity and thermoplastic tendencies becoming more pronounced at the higher MWs. Also has mechanical properties (surface tension) that cause it to separate from oil. This may become less pronounced at the higher MWs but I have not had a chance to test this at this time.
Technical info: CAS# 25322-68-3, Miscible in water at the lower MWs slowly decreasing as the MW goes up. Density: range: 1.1 to 1.2 (increases as molecular weight increases) Melting Point: Melting point increases as molecular weight increases: PEG 400 = 4-8C (39-46F) PEG 600 = 20-25C (68-77F) PEG1500 = 44-48C (111-118F)